Support-free
3MF + STL
Home & Living3 parts
Self-Draining Soap Dish
Soap dish where the soap rests on wavy ribs and water runs off over a sloped floor and an open spout, so your soap stays dry. Removable grate for rinsing, plus a wall bracket. Same shape and colours as the Toothbrush Stand. Support-free.
- Largest part
- 115 × 86 × 22 mm
- Layer
- 0.2 mm
- Material
- PETG (recommended for bathrooms) or PLA
€2.99incl. VAT
- 3MF
- STL
- Digitally checked for printability
- Prints without supports
- Download right after payment
- 3MF + STL in one ZIP
Digital product: STL and 3MF files, not a physical item. Pay with iDEAL, Bancontact, credit card or Apple Pay.
Colours in the photo
About this design
The Self-Draining Soap Dish is a soap dish you print yourself, for a bar of soap or a shampoo bar. The soap rests on wavy ribs, and water runs off over a floor with a 2 degree slope to an open spout. Your soap no longer sits in a puddle and lasts longer.
The grate sits loose in the dish, so it is easy to rinse. With the wall bracket you can hang the dish on the wall: with two 4 mm screws or an adhesive strip on the flat back.
- Dish: 115 × 86 × 22 mm, soap area 89.6 × 65.6 mm
- Removable grate: 96.8 × 72.8 × 6 mm
- Wall bracket: 40 × 25.8 × 7.3 mm
- Floor with a 2 degree slope and an open spout
- Three parts, no supports, digitally checked for printability
Print tips: print all parts flat on the bed, as oriented in the files. PETG is recommended for the bathroom, as PLA can warp with warm water. Use 3 walls and at least 5 bottom layers for the dish. Point the spout towards the sink, or place the dish on the edge.
Same shape and colours as the Toothbrush Stand with Drip Tray, so together they make a bathroom set. You get three STL files and one 3MF.
Parts and dimensions
Dimensions w × d × h, each part checked separately.
-
dish.stl
- Dimensions (w × d × h)
- 115 × 86 × 22 mm
- File
- 138 kB
-
grate.stl
- Dimensions (w × d × h)
- 96.8 × 72.8 × 6 mm
- File
- 683 kB
-
bracket.stl
- Dimensions (w × d × h)
- 40 × 25.8 × 7.3 mm
- File
- 53 kB
You get all files together in one ZIP.
- bracket.stl53 kB
- dish.stl138 kB
- drain-soap-dish.3mf208 kB
- grate.stl683 kB
110 layers of 0.2 mm (dish, 22 mm tall)
Print settings
- Layer height
- 0.2 mm
- Walls
- 3
- Infill
- 15%
- Supports
- Not needed
- Material
- PETG (recommended for bathrooms) or PLA
Designer's tip
Print all parts flat on the bed, as oriented in the files. PETG recommended: PLA can warp with warm water. Use at least 5 bottom layers for the dish. Point the spout towards the sink or place the dish on the edge. Wall bracket: two 4 mm flat-head screws, or an adhesive strip on the flat back; slide the dish down over the rail.
Frequently asked questions
Why does the soap stay dry?
The soap rests on ribs above the floor. The floor slopes 2 degrees towards an open spout, so water runs off instead of sitting under the soap.
PLA or PETG for a soap dish?
PETG. It handles warm water and moisture better. PLA can warp if warm water regularly runs over it.
Can I mount it on the wall?
Yes, with the wall bracket. Use two 4 mm flat-head screws, or an adhesive strip on the flat back. Slide the dish down over the bracket.
How do I clean it?
Lift out the grate and rinse dish and grate under the tap. Soap residue comes off easily; do not use boiling water.
License at a glance
You may
- Print for yourself, your family and as a gift
- Sell printed copies in small quantities
You may not
- Resell or share the files
- Upload the files to other platforms
Read the full license For digital content, the right of withdrawal ends once you agree to immediate delivery at checkout. Right of withdrawal
