Support-free
3MF + STL
LED & Electronics3 parts
LED controller case, fits Gledopto GL-C-015WL-D
Wall case for the Gledopto GL-C-015WL-D, the ESP32 WLED controller with microphone (measured 105 x 46 x 14 mm). The controller sits on double-sided tape in a base that slides over a dovetail rail on the wall plate; the cover clicks on. With holes for Restart and Opt/Reset, a light window for the status LED, vent slots and open notches for the power cable and the LED strip wires, which tabs on the cover close off. There is room at the bottom for a DC plug with adapter. 52 x 184 mm, 29.5 mm from the wall. Prints without supports.
- Largest part
- 52 × 184 × 24.5 mm
- Layer
- 0.2 mm
- Material
- PETG (or PLA)
€3.49incl. VAT
- 3MF
- STL
- Digitally checked for printability
- Prints without supports
- Download right after payment
- 3MF + STL in one ZIP
Digital product: STL and 3MF files, not a physical item. Pay with iDEAL, Bancontact, credit card or Apple Pay.
Colours in the photo
About this design
This LED controller case fits the Gledopto GL-C-015WL-D, the ESP32 controller with WLED and microphone for addressable LED strips. The controller (measured 105 × 46 × 14 mm, including terminal blocks and levers) sits on double-sided foam tape on two raised pads in the base. The base slides onto a dovetail rail on the wall plate from above, and the cover clicks on with sprung catches.
You lay the wires in open notches from the front: power at the bottom, up to six LED strip wires at the top. Tabs on the cover close them to a 7 mm cable hole and a 13 × 4 mm slot. The cover has 2 mm holes for Restart and Opt/Reset and a thin window that lets the status LED shine through. There is room at the bottom for a DC plug with adapter; that space assumes 45 × 14 mm, so check yours.
- Outside: 52 × 184 mm, 29.5 mm from the wall
- Inside: 48 × 180 × 20 mm, 3 mm of air above the controller
- Mounting: 2 countersunk 3.5 mm screws or 2 strips of VHB tape
- Prints without supports, diagonally on a 180 × 180 mm bed
You get the three parts (base, cover and wall plate) as separate STL files and together in one 3MF file.
Parts and dimensions
Dimensions w × d × h, each part checked separately.
-
base.stl
- Dimensions (w × d × h)
- 52 × 184 × 24.5 mm
- File
- 80 kB
-
cover.stl
- Dimensions (w × d × h)
- 52 × 184 × 13.5 mm
- File
- 100 kB
-
wall-plate.stl
- Dimensions (w × d × h)
- 52 × 184 × 6 mm
- File
- 52 kB
You get all files together in one ZIP.
- base.stl80 kB
- cover.stl100 kB
- led-controller-case-gl-c-015wl-d.3mf51 kB
- wall-plate.stl52 kB
123 layers of 0.2 mm (base, 24.5 mm tall)
Print settings
- Layer height
- 0.2 mm
- Walls
- 3
- Infill
- 20%
- Supports
- Not needed
- Material
- PETG (or PLA)
Designer's tip
Print the base and wall plate with the back on the bed and the cover with its top on the bed. Rotate all three by 45 degrees in the slicer so they fit a 180 x 180 mm bed. Mounting: screw the wall plate on with 2 countersunk 3.5 mm screws (TOP arrow pointing up) or stick it with 2 strips of VHB tape of 19 x 147 mm inside the corner marks on the back. First lay the power cable and the LED strip wires through the notches at the bottom and top, then connect them. Stick the controller onto the two raised pads with 2 mm double-sided foam tape and click the cover on: the tabs close the notches to a 7 mm cable hole and a 13 x 4 mm wire slot. Slide the base onto the rail from above. There is room at the bottom for a DC plug with adapter; that space assumes 45 x 14 mm, so check yours. Do not mount the case on or right next to metal, for good WiFi reception. You need: 2 countersunk 3.5 mm screws with wall plugs (or 2 strips of VHB tape, 19 mm wide) and 2 mm thick double-sided foam tape.
Frequently asked questions
Will the case fit my Gledopto GL-C-015WL-D?
It is designed around a measured unit: 105 × 46 × 14 mm including terminal blocks and levers, with 1 mm clearance all round and 3 mm of air above the controller. The LED and button positions are measured. If in doubt, measure your controller first.
Is this an official Gledopto product?
No. It is LayerKit's own design that fits the GL-C-015WL-D. The brand name is only there to show which controller fits.
Has this version been printed?
A test print was made of the previous version. This version was improved based on it: no pressure pins in the cover, a 1 mm deeper base, the button holes moved by 1 mm and room for a power plug. This version itself is digitally checked for fit and printability.
Does WiFi work through the case?
Yes, the case is plastic and has no metal parts. Do not mount it on or right next to metal, such as a metal cabinet or profile, as that weakens the signal.
License at a glance
You may
- Print for yourself, your family and as a gift
- Sell printed copies in small quantities
You may not
- Resell or share the files
- Upload the files to other platforms
Read the full license For digital content, the right of withdrawal ends once you agree to immediate delivery at checkout. Right of withdrawal
