Support-free
3MF + STL
LED & Electronics3 parts
LED controller case, fits Gledopto GL-C-006P
Wall case for the Gledopto GL-C-006P Pro, the Zigbee and 2.4G RF controller for CCT LED strips (measured 89 x 44 x 24 mm). The controller sits on double-sided tape in a base that slides over a dovetail rail on the wall plate and clicks into place over the last few millimetres; the cover clicks on. Open notches for a flat power cable and three strip wires, which tabs on the cover close off, tie-wrap eyelets for strain relief and vent slots. 50 x 131 mm, 39.5 mm from the wall or cabinet. Prints without supports.
- Largest part
- 50 × 131 × 34.5 mm
- Layer
- 0.2 mm
- Material
- PETG (or PLA)
€2.99incl. VAT
- 3MF
- STL
- Digitally checked for printability
- Prints without supports
- Download right after payment
- 3MF + STL in one ZIP
Digital product: STL and 3MF files, not a physical item. Pay with iDEAL, Bancontact, credit card or Apple Pay.
Colours in the photo
About this design
This LED controller case fits the Gledopto GL-C-006P Pro, the controller for CCT LED strips with Zigbee and 2.4G RF. The controller (measured 89 × 44 × 24 mm) sits on double-sided foam tape on two raised pads in the base, with clamping ribs along the sides. The base slides onto a dovetail rail on the wall plate from above and clicks into place over the last few millimetres, so it stays put even when the plate is mounted horizontally, for example under a shelf. The cover clicks on with sprung catches.
You lay the flat power cable (2 × 0.75 mm²) and the three LED strip wires in open notches from the front. Tabs on the cover close them to slots of 9 × 4.5 and 8 × 3 mm. Behind each entry there is an eyelet for a tie wrap as strain relief. Vent slots in the cover and side walls let heat out.
- Outside: 50 × 131 mm, 39.5 mm from the wall or cabinet
- Inside: 46 × 127 × 30 mm
- Mounting: 2 countersunk 3.5 mm screws or 2 strips of VHB tape
- Prints without supports, fits a 180 × 180 mm bed
You get the three parts (base, cover and wall plate) as separate STL files and together in one 3MF file.
Parts and dimensions
Dimensions w × d × h, each part checked separately.
-
base.stl
- Dimensions (w × d × h)
- 50 × 131 × 34.5 mm
- File
- 109 kB
-
cover.stl
- Dimensions (w × d × h)
- 50 × 131 × 8.2 mm
- File
- 73 kB
-
wall-plate.stl
- Dimensions (w × d × h)
- 50 × 131 × 6.6 mm
- File
- 52 kB
You get all files together in one ZIP.
- base.stl109 kB
- cover.stl73 kB
- led-controller-case-gl-c-006p.3mf51 kB
- wall-plate.stl52 kB
173 layers of 0.2 mm (base, 34.5 mm tall)
Print settings
- Layer height
- 0.2 mm
- Walls
- 3
- Infill
- 20%
- Supports
- Not needed
- Material
- PETG (or PLA)
Designer's tip
Print the base and wall plate with the back on the bed and the cover with its top on the bed. Mounting: screw the wall plate on with 2 countersunk 3.5 mm screws (TOP arrow pointing up) or stick it on or inside a cabinet with 2 strips of VHB tape of 19 x 94 mm inside the corner marks on the back. First lay the flat power cable (2 x 0.75 mm2) and the three LED strip wires through the notches at the bottom and top, connect them and secure them with a tie wrap through the eyelet behind each entry (tie wraps up to 3.6 mm wide). Stick the controller onto the two raised pads with 2 mm double-sided foam tape and click the cover on: the tabs close the notches to slots of 9 x 4.5 and 8 x 3 mm. Slide the base onto the rail from above until it clicks. The cover has no opening for a button or LED; take the cover off to pair again. Do not mount the case on or right next to metal, for good Zigbee and RF reception. You need: 2 countersunk 3.5 mm screws with wall plugs (or 2 strips of VHB tape, 19 mm wide), 2 mm thick double-sided foam tape and 2 small tie wraps.
Frequently asked questions
Will the case fit my Gledopto GL-C-006P Pro?
It is designed around a measured unit of 89 × 44 × 24 mm, with 1 mm clearance all round and 3 mm of air above the controller. The power notch sits in the middle of the short side and is made for a flat cable of about 7 × 3.5 mm.
Can I reach the controller's button or LED?
No, the cover has no opening for a button or LED. To pair the controller again, click the cover off.
Do Zigbee and the RF remote work through the case?
Yes, the case is plastic and has no metal parts. Do not mount it on or right next to metal, as that weakens the signal.
Has this case been printed?
No, this is the first version and it has not been printed yet. It is digitally checked: the controller, cable and wires fit without clashing, the cover closes and all parts print without supports.
License at a glance
You may
- Print for yourself, your family and as a gift
- Sell printed copies in small quantities
You may not
- Resell or share the files
- Upload the files to other platforms
Read the full license For digital content, the right of withdrawal ends once you agree to immediate delivery at checkout. Right of withdrawal
