Support-free
3MF + STL
Home & Living2 parts
Hex Jewelry Stand
Honeycomb panel for earrings and necklaces on a hexagonal dish. Hook earrings hang in the open cells, studs go into the small holes along the edge and necklaces rest in the notches on top. The base has room for rings. Two parts that slot together, prints without supports.
- Largest part
- 129.3 × 112 × 15 mm
- Layer
- 0.2 mm
- Material
- PLA or PETG
€2.99incl. VAT
- 3MF
- STL
- Digitally checked for printability
- Prints without supports
- Download right after payment
- 3MF + STL in one ZIP
Digital product: STL and 3MF files, not a physical item. Pay with iDEAL, Bancontact, credit card or Apple Pay.
Colours in the photo
About this design
The Hex Jewelry Stand is a hexagonal honeycomb panel that stands in a dish. Hook earrings hang in the open 10 mm cells, studs go into the 30 small holes along the edge and necklaces rest in the 5 notches on top. The two compartments in the base hold rings and loose earrings.
- Panel 124 × 107 mm, 3.2 mm thick
- Base 112 mm across the flats, 15 mm tall
- Total height about 122 mm
- The panel tab clamps into the slot of the base, no glue needed
- Prints without supports, digitally checked for printability
Print tips: print the panel flat and the base upright, as supplied. 0.2 mm layers, 3 walls and 20% infill. The stud holes are 1.6 mm; widen them with a needle if needed. Looks great in two colours: panel and base each in their own colour.
You get two STL files and one 3MF.
Parts and dimensions
Dimensions w × d × h, each part checked separately.
-
earring-stand-panel.stl
- Dimensions (w × d × h)
- 123.3 × 117.4 × 3.2 mm
- File
- 321 kB
-
earring-stand-base.stl
- Dimensions (w × d × h)
- 129.3 × 112 × 15 mm
- File
- 6 kB
You get all files together in one ZIP.
- earring-stand-base.stl6 kB
- earring-stand-hex.3mf70 kB
- earring-stand-panel.stl321 kB
75 layers of 0.2 mm (earring stand base, 15 mm tall)
Print settings
- Layer height
- 0.2 mm
- Walls
- 3
- Infill
- 20%
- Supports
- Not needed
- Material
- PLA or PETG
Designer's tip
Print the panel flat and the base upright, as supplied. The small stud holes are 1.6 mm; widen them with a needle if needed. The tab of the panel clamps into the slot of the base. Looks great in two colours: panel and base each in their own colour.
Frequently asked questions
Do stud earrings fit the holes?
The holes are 1.6 mm, wide enough for the post of a stud earring. If your printer runs a bit tight, open them up with a needle.
Do I need to glue the parts?
No. The tab at the bottom of the panel clamps into the slot of the base, so you can also store the stand flat.
Where do necklaces go?
There are 5 V-notches on top of the panel. Lay the necklace in a notch and it hangs down on both sides without tangling.
License at a glance
You may
- Print for yourself, your family and as a gift
- Sell printed copies in small quantities
You may not
- Resell or share the files
- Upload the files to other platforms
Read the full license For digital content, the right of withdrawal ends once you agree to immediate delivery at checkout. Right of withdrawal
