Nederlands English
Cart 0
Pocket phone stand

Support-free

3MF + STL

  • Show image 1: Pocket phone stand

Desk3 parts

Pocket phone stand

Phone stand that packs flat to 78 x 72 x 16 mm. Slide the two side pieces and two bars together and your phone stands at 65 degrees, portrait or landscape, in a case up to 12 mm thick. Handy for travel, the office or the dinner table.

Largest part
72 × 77.5 × 4 mm
Layer
0.2 mm
Material
PLA or PETG

€1.99incl. VAT

  • 3MF
  • STL
  • Digitally checked for printability
  • Prints without supports
  • Download right after payment
  • 3MF + STL in one ZIP

Digital product: STL and 3MF files, not a physical item. Pay with iDEAL, Bancontact, credit card or Apple Pay.

Colours in the photo

About this design

The Pocket phone stand is a phone stand you take apart and carry flat. Disassembled it is a 78 × 72 × 16 mm pack that fits a bag or jacket pocket. There are no hinges: you slide two side pieces and two bars together.

  • Assembled: 66 × 72 × 77.5 mm, 65 degree viewing angle
  • Packed: 72 × 77.5 × 16 mm
  • Phone in portrait or landscape, in a case up to 12 mm thick
  • Four 4 mm thick parts, no supports, digitally checked for printability

Print tips: print the side piece twice and each bar once, all flat. 0.2 mm layers, 3 walls, 30% infill, PLA or PETG. The slots are 0.2 mm wider per side than the plate; push the parts firmly together. If it is too tight, give the slot a quick pass with a small file.

Handy when travelling, at the office or at the table for a recipe or video call. You get three STL files and one 3MF.

Parts and dimensions

Dimensions w × d × h, each part checked separately.

  • 72 mm 4 mm

    pocket-phone-stand-side.stl

    Dimensions (w × d × h)
    72 × 77.5 × 4 mm
    File
    23 kB
    Supports: None
  • 66 mm 4 mm

    pocket-phone-stand-front-bar.stl

    Dimensions (w × d × h)
    66 × 16 × 4 mm
    File
    19 kB
    Supports: None
  • 66 mm 4 mm

    pocket-phone-stand-back-bar.stl

    Dimensions (w × d × h)
    66 × 12 × 4 mm
    File
    19 kB
    Supports: None

You get all files together in one ZIP.

  • pocket-phone-stand-back-bar.stl19 kB
  • pocket-phone-stand-front-bar.stl19 kB
  • pocket-phone-stand-side.stl23 kB
  • pocket-phone-stand.3mf14 kB

20 layers of 0.2 mm (pocket phone stand side, 4 mm tall)

Layer height
0.2 mm
Walls
3
Infill
30%
Supports
Not needed
Material
PLA or PETG

Designer's tip

Print the side piece twice and each bar once, all flat as supplied. The slots are 0.2 mm wider per side than the plate: push the parts firmly together. If it is too tight, give the slot a quick pass with a small file.

Frequently asked questions

Does the stand fold?

No, it has no hinges. You take the four flat parts apart and slide them together again later. Packed, they measure 78 × 72 × 16 mm.

Will my phone fit with its case?

Yes, with a case up to 12 mm thick, in portrait or landscape.

The parts are too tight. What now?

The slots have 0.2 mm clearance per side. If they are too tight, run a small file or sandpaper through the slot.

License at a glance

You may

  • Print for yourself, your family and as a gift
  • Sell printed copies in small quantities

You may not

  • Resell or share the files
  • Upload the files to other platforms

Read the full license For digital content, the right of withdrawal ends once you agree to immediate delivery at checkout. Right of withdrawal