Support-free
3MF + STL
Kitchen2 parts
Fridge Can Dispenser
Rolling chute for 5 cans of 330 ml (66 mm): take the front can and the next one rolls forward by itself. End stop with a hexagonal cut-out, honeycomb floor and stackable. Two 170 mm parts that slot together, each fits a small bed. Can be adjusted for slim cans too. Prints without supports.
- Largest part
- 125.3 × 169.5 × 58.7 mm
- Layer
- 0.2 mm
- Material
- PETG or PLA
€2.99incl. VAT
- 3MF
- STL
- Digitally checked for printability
- Prints without supports
- Download right after payment
- 3MF + STL in one ZIP
Digital product: STL and 3MF files, not a physical item. Pay with iDEAL, Bancontact, credit card or Apple Pay.
Colours in the photo
About this design
The Fridge Can Dispenser is a rolling chute for 5 cans of 330 ml. The floor slopes 2.5 degrees towards the front: take the front can and the next one rolls forward to the end stop by itself. The end stop has a hexagonal cut-out for your fingers.
- Size: 125 x 340 x 59 mm
- For cans of 66 mm diameter and 115 mm long
- Two 170 mm parts that you lower onto each other with dovetails
- Honeycomb floor, stackable thanks to a ridge on the walls
- Can be adjusted for slim cans
- Prints without supports, digitally checked for printability
Print tips: print the front and back part upright, as supplied. Each part fits a 180 mm bed. 0.2 mm layers, 3 walls, 15% infill, PETG or PLA. Load it from the back. It fits a fridge shelf at least 35 cm deep and 13 cm wide.
You get two STL files and one 3MF.
Parts and dimensions
Dimensions w × d × h, each part checked separately.
-
fridge-can-dispenser-front.stl
- Dimensions (w × d × h)
- 125.3 × 180 × 58.7 mm
- File
- 168 kB
-
fridge-can-dispenser-back.stl
- Dimensions (w × d × h)
- 125.3 × 169.5 × 58.7 mm
- File
- 159 kB
You get all files together in one ZIP.
- fridge-can-dispenser-back.stl159 kB
- fridge-can-dispenser-front.stl168 kB
- fridge-can-dispenser.3mf63 kB
294 layers of 0.2 mm (fridge can dispenser front, 58.7 mm tall)
Print settings
- Layer height
- 0.2 mm
- Walls
- 3
- Infill
- 15%
- Supports
- Not needed
- Material
- PETG or PLA
Designer's tip
Print the front and back part upright as supplied. Lower the back part from above onto the two dovetails of the front part. Load it from the back and the cans roll forward. Fits a fridge shelf at least 35 cm deep and 13 cm wide. To stack, put the second dispenser straight on top: the ridge on the walls drops into the grooves under the floor. For slim cans, set CAN_D and CAN_L.
Frequently asked questions
Do slim cans fit?
By default it is made for regular 330 ml cans (66 mm). For slim cans set CAN_D to 58 and CAN_L to 146 and print again; it then gets wider.
Will it fit my fridge?
You need a shelf at least 35 cm deep and 13 cm wide, with about 6 cm of height. Two stacked need about 12 cm.
Why is it made of two parts?
For 5 cans the chute is 340 mm long. Split into two 170 mm parts it also fits a small printer.
License at a glance
You may
- Print for yourself, your family and as a gift
- Sell printed copies in small quantities
You may not
- Resell or share the files
- Upload the files to other platforms
Read the full license For digital content, the right of withdrawal ends once you agree to immediate delivery at checkout. Right of withdrawal
